Norwood Parade Auto Spares

234 the Parade, Norwood, Adelaide, South Australia 5067

Ph 08 8332 8011 open 7 days www.derek.com.au

Email derek@derek.com.au

L.E.D. Trailer Lights

HELLA

Hella Australia's growing range of LED (Light Emitting Diode) lamps has been accepted as the most advanced one-step solution to problems of lighting in the commercial transport industry.

Since the Hella LED lighting system was first introduced only a few years ago, its advanced and innovative technology has set new standards and received considerable worldwide recognition.

Hella is one of the largest LED component buyers in the world, and we have developed the
technologies that have built millions of units, engineered and tested to the highest standards.

Features & Benefits

LED Technology has enormous benefits for the transport industry, the most obvious being the reduction in maintenance requirements allowing transport operators to significantly reduce vehicle servicing down times, as there are no globes to burn out or holders to corrode.

Hella’s LED lamps are pre-wired for easy installation and manufactured from a new generation acrylic material with enhanced impact resistance and high tolerance to chemicals, salt spray and cleaning fluids for ultra-long service life. Hella’s LED lamps operate with up to 60% less current draw than comparable globe lamps and are required to remain fully operational under severe cold, heat and humidity while being subjected to high levels of vibration. Hella Australia has extensive test and development facilities to prove all of our products, which is why Hella LED lamps come with a 5 year unlimited mileage warranty.

Hella LED lamps are now available for truck, trailer, bus, caravan, marine, mining, emergency and specialty applications. The range includes a large variety of indicators, markers, stop/ rear position, signal, multifunction, reversing and licence plate lamps.

LED Multivolt Technology

One of the leading advantages of Hella’s new LED Technology is the unique multivolt circuitry fitted to most LED lamps ensuring a uniform level of intensity and full light output at any voltage between 8 to 28 volts or 9 to 33 volts. Both configurations allow multivolt LED lamps to be connected to either 12V or 24V electrical systems without modification or the light output being adversely affected by voltage drop often encountered in trailer systems.

DuraLed® Signal Lamps

DuraLed lamps feature unique registered designs with shallow shapes and covered mounting screws for enhanced protection against damage. All lamps are pre-wired with twin-core sheathed cable, fully sealed against dust and moisture to International Protection Standards IP6K6 and IP6K7 and compliant with current ADR (Australian Design Rules), thus approved for use in Australia and New Zealand. The range includes Multivolt Marker Lamps, Multivolt Indicators, Multivolt High Intensity Warning Signal Lamps and a Combination Stop/Rear Position/indicator Lamp with special wide-angle optics for enhanced visibility.




DuraLed® Features

Unique multivolt circuitry ensures uniform level of intensity and full light output at any voltage between 8 to 28 volts or 9 to 33 volts
Up to 60% less current draw than comparable globe lamps
Ultra-long service life
Vibration and shock resistant
Fully sealed against dust and moisture to International Protection (IP) Standards IP6K6 and IP6K7
Ultra-fast response times
Reverse polarity protected
Pre-wired for easy installation
ADR compliant. Approved for use in New Zealand and Australia
Three year unlimited kilometres warranty – mechanical and accident damage excluded.

EuroLED® Signal Lamps

Hella has introduced a new range of multivolt EuroLED Stop/ Rear Position, Rear Direction Indicator and Reversing Lamps specifically designed for the bus and coach industry. For the first time, Hella offers matching LED signal lamps to suit all rear functions, including reverse, allowing transport operators to upgrade all required signal lamps on both side and rear of the vehicle to the latest in multivolt LED technology.

The combined use of high-performance single LED technology and precision optics results in a brilliant look along with the benefit of low power consumption. All EuroLED signal lamps are equipped with multivolt electronics for optimum brightness at any input voltage between 9 to 33 volts and feature special wide-angle optics for significantly improved side visibility. The lens is made from acrylic with enhanced impact strength and improved tolerance to chemicals whilst the unique shallow design and low lamp profile effectively reduce the risk of mechanical damage.

EuroLED Signal Lamps are shock proof, resistant to vibration and fully
sealed to withstand high-pressure washing to ensure long service life
and maximum durability.




EuroLED® Features:

Latest high-performance, single LED design.
Multivolt for optimum brightness at input voltages from 9 to 33 volts.
Ultra low power consumption of less than 0.5 watt for the rear position lamp; 2.5 watts for the stop, rear direction indicator and reversing lamps.
Fully sealed to withstand high-pressure washing – degree of protection IP6K6 and IP6K7.
Ultra-long service life.
Vibration and shock resistant.
Ultra fast response time, up to 100 times faster than conventional globe lamps.
Lens made from acrylic with enhanced impact strength – which means greater tolerance to chemicals.
Reverse polarity protected.
Pre-wired with 2.5 metres of cable for easy installation.
Surface mount (mounting bushes included).
Five-year warranty (mechanical damage excluded).
ADR and ECE compliant – approved for use in Australia, New Zealand and

Part No. 2379 DuraLed Triple Combination Lamp trailer lamp

Description
Compact LED Stop/ Rear Position/ Rear Direction Indicator Lamp with ultra wide-angle optics for improved visibility. Suitable for light commercial and boat trailers. Shockproof, vibration resistant and fully sealed to withstand water submersion and high-pressure washing.

Voltage
Multivolt (8-28V DC).

Wattage
Stop - 5W
Rear Position - 1W
Indicator - 1W

Mounting
To be mounted horizontally. Screw caps and mounting bushes included.

Spare Parts
9.2330.08 - Screw cap & boss kit

Cable Length
6 metres

Note
For heavy duty transport or construction vehicles and/or where separate lamps are required for each function, Hella recommends the DuraLed Multivolt Signal Lamp Range

L.E.D. Trailer Lights

Licence Plate 35 Series

Description

• Licence plate lamp is designed to be fitted centered above the licence plate, only one required for ADR.
• Two lamps required when fitting to European licence plates style A and style B.
• Corrosion protection with tinned copper cable upto 6 metres.
• 5 Year Warranty and ADR Approved.
• Lamps have standard 40cm hardwired and 6 metre cable available.

35BLM - Blister
35BLMB - Bulk
35BLM6 - Bulk
35CLM - Blister
35CLM6 - Bulk
35BL - Bulk
35CL - Bulk

Specifications

• 35 BLM/CLM Multivolt 12-24 volt,
• Overall size
35BLM/35CLM 76 x 41 x 30mm
• Current draw @13.8volts
35BLM/35CLM 0.04Amps
• 35BLM/35CLM ADR 48/00
CRN 36280.

Generation II 100 Series

Description
• Australian design registered number 316651.
• Designed using smart technology with the least amount of
components required to pass ADR standards.
• Lifetime Warranty and ADR Approved.
• Plug in and drive away cable assemblies available.
• Fully Submersible and rust proof.
• Corrosion protected tinned copper wiring.
• Specially designed male & female 4 pin plugs.
• Circuit board and components fully encased in resin.
• Slimline design 22mm, stainless steel nuts and bolts.
• Technical drawings PDF click at bottom of page.
• Accessories available in the Wiring systems section

100BAR - Black base white background in a bulk pack of 1
100BAR2 - Black base white background blister pack of 2

100BARB - Black base black background Bulk pack of 1
100BARB2 - Black base black background blister pack of 2

100ARM - Grey base white background blister pack of 1
100BARZ - Blck base white background with blister pack of 1

Specifications
• 100BAR & 100BARB 12 volt only
• 100ARM Dual Voltage 12 volt - 24 volt.
• Overall size 100 x 100 x 22mm.
• Current draw @13.8volts
Stop 0.15Amps, Tail 0.07Amps
Ind 0.11Amps,
• 100BAR, 100BARB and 100ARM
ADR 49/00 CRN 37986
ADR 6/00 Cat2 CRN 37985
ADR 47/00 CRN 38102
• Mounting instructions refer ADR 13/00.

Generation II 150 Series

Description
• Australian design registered number 316651.
• Designed using smart technology with the least amount of components
required to pass ADR standards.
• Lifetime Warranty and ADR Approved.
• Plug in and drive away cable assemblies available.
• Fully Submersible and rust proof.
• Corrosion protected tinned copper wiring.
• Specially designed male & female 4 pin plugs.
• Circuit board and components fully encased in resin.
• Slimline design 22mm, stainless steel nuts and bolts.
• Technical drawings PDF click at bottom of page.
• Accessories available in the Wiring systems section

150BAR - Black base white background in a bulk pack of 1
150BAR2 - Black base white background blister pack of 2 $59.95

150BARB - Black base black background Bulk pack of 1
150BARB2 - Black base black background blister pack of 2

150ARM - Grey base white background blister pack of 1

Specifications
• 150BAR & 150BARB 12volt only
150ARM Dual Voltage 12 volt - 24 volt.
• Overall size 150 x 80 x 22mm.
• Current draw @13.8volts
Stop 0.15Amps, Tail 0.07Amps Ind 0.11Amps,
• 150BAR, 150BARB and 150ARM
ADR 49/00 CRN 37986
ADR 6/00 Cat2 CRN 37985
ADR 47/00 CRN 38102.

• Mounting instructions refer ADR 13/00.

Part Legends
Part No Legend
100 - Size of lamp
2 - Two in a blister
A - Amber Led
R - Red Led
M - Multivolt
B after 150 - Black Base
B - Black Background

Accessories for Gen II Lamps
• Cable accessories in the wiring systems section, many combinations available.
Entire system will never need to be wire stripped or joined, including the trailer plug.

• LP1 Licence plate in the Licence plate section has a plug with one metre of wire which can be connected to the back of the Gen II lamps.

Generation II 275 Series

Description
• Australian design registered number 316650.
• Designed using smart technology with the least amount of
components required to pass ADR standards.
• Lifetime Warranty and ADR Approved.
• Plug in and drive away cable assemblies available.
• Fully Submersible and rust proof.
• Corrosion protected tinned copper wiring.
• Specially designed male & female 4 pin plugs.
• Circuit board and components fully encased in resin.
• Slimline design 22mm, stainless steel nuts and bolts.
• Technical drawings PDF click at bottom of page.
• Accessories available in the Wiring systems section

275BAR - Black base white background in a bulk pack of 1
275BAR2 - Black base white background blister pack of 2

275BARB - Black base black background Bulk pack of 1
275BARB2 - Black base black background blister pack of 2

275ARM - Grey base white background blister pack of 1 $59.95

Specifications
• 275BAR & 275BARB 12volt only
275ARM Dual Voltage 1 volt - 24 volt.
• Overall size 275 x 100 x 22mm.
• Current draw @13.8volts
Stop 0.20Amps, Tail 0.09Amps Ind 0.14Amps,
• 275BAR, 275BARB and 275ARM
ADR 49/00 CRN 38658
ADR 6/00 Cat2 CRN 38657
ADR 47/00 CRN 38102.

• Mounting instructions refer ADR 13/00.

Part Legends
275- Size of lamp
2 - Two in a blister
A - Amber Led
R - Red Led
M - Multivolt
B after 275 - Black Base
B - Black Background


Packing Availability: Blister Pack,Bulk
Approval's: ADR Approved

LP1 Licence plate assembly

Description
• Australian design pending for LP1.
• Designed for standard Australian licence plate.
• 4 holes on assembly are the same dimension as the standard Australian licence plate.
• 6 LED two lamp assembly concealed in frame.
• One metre twin sheathed cable with connector plug is adaptable to Gen II lamps and can be cut off if necessary for other products.
• 30mm x 350mm lamp cover conceals the lamps and can be used for your company name or logo.
• 5 Year Warranty and ADR Approved.

LP1 - Blister

Specifications
• Multivolt 12-24 volt,
• Overall size
375 x 173 x 24.5mm
• Current draw @13.8volts
0.11Amps
• ADR 48/00 CRN 39611.

• Mounting instructions refer ADR 13/00.

ARK Trailer Light Board
Removable trailer light board with 8m cable, available in

1.5m with 7 pin round plug (762975),

1.8m with 7pin round plug (762978)

1.5m with 7 pin flat plug (762979).

Replacement lens and lights to suit available.

TRAILER LIGHTS

Part No: FL770B

ADR Approved square combination lamp features stoplight, blinker, tail light and reflector.

Includes all required bulbs and screws.

Bayonet fittings.

Part No: FL660B

ADR Approved rectangular combination lamp features stoplight, blinker, tail light and reflector.

Includes all required bulbs and screws.

Bayonet fittings.

Part No: FL600B

Rectangular shaped combination lamp includes flasher,
brake and tail lights, all screws and festoon bulbs.

Part No: FL1003AB

12V round 3” - 75mm indicator lamp complete with
mounting screws & festoon bulb.

Part No: FL1003CB

12V round 3” - 75mm clear lamp complete with mounting screws & festoon bulb.

Part No: FL1003RB

12V round 3” - 75mm tail lamp complete with mounting screws & festoon bulb.

Part No: FL1002B

12V round 3” - 75mm combination tail light & indicator lamp.

Complete with mounting screws & festoon bulb.

Part No: FL1004B

12V round 3” - 75mm stop, tail & number plate lamp complete with mounting screws & festoon bulb.

Part No: FL200B

Coffin shaped combination lamp includes flasher, brake
and tail lights, all screws and festoon bulbs.

4WD COVERS AH GO GAH HORN AIR FILTERS AIR HORNS ARMREST ASHTRAYS AUTO ACCESSORIES AUTO DRY WASH CLOTHS BABY BOLTS BACK SUPPORTS BADGES BATTERY CHARGERS BATTERY ISOLATOR SWITCH BLIND SPOT MIRRORS BOAT POLISH BOAT WASH BOAT WAX BODY FILLERS BOG BRAKE LIGHT REPAIR KIT BRAKE SHOES BUG SCREENS BULBS BUMPER SPRAY CABLE TIES CAR BATTERIES CAR COVER CAR MATS CAR STANDS CARAVAN COVERS CENTRE CONSOLES CHARGE AND MAINTAIN CHEMICALS CHEMIWELD COMPRESSION TESTER COOLANTS COOLING FANS CUT AND SHAPE MIRROR D SHACKLES DEGREASERS DISC PADS DISC PADS DOOR EDGE PROTECTORS DRI-LUBE DRIVE BELTS DRIVE SHAFTS DRIVING LIGHTS ELECTRIC WATER PUMPS ELECTRICAL TAPE ELECTRONIC IGNITION ENGINE PUMPS EXHAUST CLAMPS FAN BELTS FIBERGLASS FISHING ROD HOLDERS FOOT PUMPS FUEL CANS FUEL FILTERS FUEL HOSE GASKETS GLOSS BLACK GOGGLES H4 LIGHTS H7 LAMPS HAND PUMPS HEATER HOSES HELLA LAMPS HOSE CLAMPS HOUSINGS HYDRAULIC JACKS IGNITION COILS IGNITION LEADS INDUSTRIAL BELTS JACKS JOCKEY WHEELS JUMPER LEADS KEY FOBS L PLATES LEAD REPLACEMENT ADDATIVE LED HEADLAMPS LED LIGHTS LED TORCHES LENS REPAIR KITS LENS TINT LITTER BINS MAG WHEEL CLEANERS MASKING TAPE MASKS MATT BLACK MICRO CHAMOIS MICRO FIBRE CLOTHS MIRRORS MOTHER'S WAX ATTACK POLISHER MOTHERS WAX ATTACK POLISHER MOTOR BIKE STRAPS MUSICAL AIR HORN NAVIGATION LIGHTS NECK SUPPORTS NOLTEC SOFTRIDE URETHANE BUSHES OCCY STRAPS OIL CAPS OIL FILTERS P PLATES PAINT PAINT PETROL CAPS PHILLIPS LAMPS PLASTIC CHAMOIS PLASTIC DYE PLUGS POLISHES POLSHING CLOTHS PROJECTA RACK ENDS RADIATOR CAPS RADIATOR HOSES RECOVERY STRAPS RED BACK SPIDER GEAR KNOBS ROK STRAPS ROOF BARS ROOF BASKETS ROOF RACKS SEAT BELTS SEAT COVERS SLICK50 SLICK 50 SNATCH STRAPS SOLAR PANELS SPANNERS SPARE WHEEL COVERS STAINLESS STEEL BOLTS STEERING WHEEL COVERS SURGE GUARDS SWITCHES SYNTHETIC CHAMOIS SYNTHETIC OILS THERMOSTATS THINNERS TIE ROD ENDS TIMING BELTS TIMING LIGHTS TOOLS TOOLS TOP COAT CLEAR TOW HOOKS TOW ROPES TRAILER CABLE TRAILER LAMPS TRIPLE AIR HORNS TROLLEY JACKS TRUCK HOSES TRUCK WASH TUBE PATCHES TUBELESS TYRE REPAIR KITS TRUCK JUMPER LEADS TWIN AIR HORNS TYRE SPRAY TYRE VALVES UNIVERSAL JOINTS UTE HOOKS VACUMN TESTER WALL PROTECTORS WASHER MOTORS WATER HOSE WATER PUMPS WATERPROOF TRAILER LAMPS WHEEL BRACES WHEEL CHOCKS WHEEL CYLINDERS WINDOW SHADES WINDOW SOX WINDSCREEN WIPERS WIPER ARMS WIPER BLADES WIPER JETS WIPER MOTORS WIPER REFILLS