Norwood Parade Auto Spares

234 the Parade, Norwood, Adelaide , South Australia, 5067

Phone / Fax 08-8332 8011.............Email derek@derek.com.au

" For all your auto parts and accessories " WWW.DEREK.COM.AU

Trading Hours

MON TO FRI 8.30am - 6.00pm
THU 8.30am - 7.00pm
SAT 9.00am - 4.00pm
SUN 10.00am - 4.00pm
HOLIDAYS 10.00am - 4.00pm
OPEN 365 DAYS A YEAR

CTEK

XC800 6 VOLT BATTERY CHARGE AND MAINTAIN $79.95 postage $10.00

For those with 6V batteries
The XC 800 is the battery charger that can give your old car a new lease on life.

This is a complete 6V battery charger in a diminutive format that charges everything from small batteries of 1Ah up to large tractor batteries.

Features
Four step, fully automatic switch mode model.
Charges lead-acid batteries (Wet, MF, GEL and AGM) from 1.2Ah to 32Ah, 1.2-100Ah maintenance charging.
Maintenance pulse charging increases battery life and gives superb performance.
Charges even drained batteries. Pulse recover of slightly sulphated batteries.
Low back current drain, low ripple and input voltage independent (170-260V).
High efficiency: 85%
Delivered with two interchangeable connection leads, one with clamps, and one with eyelet terminals.
The charger can be connected for months, ideal for seasonal vehicles.
Compact design with mounting holes for permanent assembly.
5 year warranty.
Batteries
The XC 800 charges 6V lead-acid batteries (Wet, MF, GEL and AGM) from 1.2Ah to 32Ah.

You will find an explanation of the various battery types under Charger University, Battery Types.

The charger can also be used for maintenance charging of 6V lead-acid batteries from 1.2Ah to 100Ah.

The XC 800 is easy to use.

You do not need to make any settings.

The charger adapts the charge to suit the battery and switches to pulse maintenance charging when the battery is fully charged.

Mounting
The charger is easily fitted in place using two screws. The diameter of the mounting holes is 4.2mm located as shown in the image. The image also shows the dimensions of the charger.

Safety
Electronic safe, the charger will not damage vehicle electronics. The battery does not normally need to be disconnected from the vehicle when charging.
Minimal gas build-up and a patent-pending spark protection system.
Short circuit and reverse polarity protected.
Double insulation.
Splash and dust proof (IP65) and approved for outdoor use.
Progressive temperature protection.
Tested and approved by Intertec SEMKO AB. S-marked and conforms to the following standards: EN 60335-1, EN 60335-2-29, EN 55014-2, EN 55022, EN 61000-3-2 and EN 61000-3-3

Equipment
The XC 800 is delivered with two different battery leads, one with clamps and one with eyelet terminals, all colour coded for easy +/- identification.

If the battery is difficult to access, the lead with eyelet terminals can be mounted to the battery, and the quick connectors are located so that it is easily reached for charging.

You can also purchase additional leads allowing you to have one lead with eyelet terminals fixed to all your vehicles with batteries that are difficult to get at, and charge them simply from the same charger.

Charging
The XC 800 has a fully automatic, four step charge:

1.Desulphation
Desulphation with pulsing for sulphated batteries.
2.Bulk
Primary charging where approximately 80% of the charging takes place. The charger delivers maximum current until the terminal voltage has risen to the preset level. After a number of hours, the charger goes on to the next phase, even if maximum voltage is not reached.
3.Absorption
Final charging, voltage is kept at the preset level. During this phase, the current is gradually reduced. If the maximum length of time for Absorption is exceeded, the charger automatically continues with Analysis.
4.Maintenance charging - pulse
State of charge varies between 95% and 100%. The battery receives a pulse when the voltage sinks, keeping the battery in good shape when it is not being used. The charger can be connected for months at a time. If the battery is charged and/or the battery’s terminal voltage drops, the charger starts a charge pulse until the voltage has reached the preset level. The charge pulse is then interrupted and the cycle is repeated as long as the charger is in pulse maintenance phase. If the terminal voltage drops even lower, the charger automatically reverts to the beginning of the charging curve. If possible, check the water level in the battery.
Using the XC 800 gives your battery an optimum service life and operational reliability.

Technical Data
MODEL XC 800
Input voltage AC 170-260VAC, 50-60Hz
Output voltage Nominal: 6V
Efficiency 85%
Charging voltage 7.2V
Charging current 0.8A max
Back current drain* <1mA
Ripple** 10mV rms, 12mA (2%)
Ambient temperature -20°C to +50°C, output power is reduced automatically at higher temperatures.
Type of charger Four step, fully automatic switch mode with pulse maintenance.
Type of batteries 6V lead-acid batteries (Wet, MF, AGM and GEL)
Battery capacity 1.2-32Ah (1.2-100Ah maintenance charging)
Dimensions (L x W x H) 142x51x36mm
Insulation IP 65 (splash and dust proof)
Weight 0.3kg

*) Back current drain is what drains the battery if the charger is connected without the power cord connected. The XC 800's extremely low back current drain corresponds to < 1 Ah per month. Many other chargers have 1 Ah per day.

**) Ripple denotes the amount of interference there is to the current and voltage. A high current ripple heats the battery and shortens its life. A linear charger has a current ripple of 70 - 400% which is much larger than the maximum 5% for a modern sealed battery. Voltage ripple could harm other equipment, which is connected to the battery. XC 800's ripple is only 2%. The battery gains a long service life and there is no risk of damage to other electronic devices connected to the battery.

Projecta Charge and Maintain

AC150
Automatic 12V 1.5A* 900mA Battery Charger $49.95
Charge N' Maintain

FEATURES
Charge N' Maintain - Automatic Charging
Automatically stops charging when the battery is full. You can leave the charger connected to the battery without the risk of overcharging.

Charge N' Maintain - Automatic Maintenance
Once the battery is full, the charger automatically starts to maintain the battery. The charger monitors the battery voltage and continues to top up the battery, keeping it fully charged and ready for use.
Thermal Overload/Polarity Protection
Prevents the output leads from sparking due to accidental reverse connection or short circuit, increasing safety.
60cm Wiring Harness
A 60cm harness allows for easy connection to vehicles that have hard to reach batteries. Includes an inline fuse to protect the harness from short circuits.
* The term "1.5A" as opposed to "900mA" is an Amps RMS rating used as an industry reference and not the actual DC output.

SPECIFICATIONS
PART NO. AC150
TYPE Automatic
INPUT 240V, 50Hz, 17W
OUTPUT 900mA (1.5A RMS*) at 12.0V
CHARGE CONTROL
Cut out: 14.2V
Cut in: 13.4V
Start: 5.0V
APPROVALS Electrical Safety, EMC
L.E.D CHARGE INDICATION
RED LIGHT ON Power on
AMBER
LIGHT ON Charging
GREEN LIGHT ON
Fully charged. Turn off the charger and disconnect.
BATTERY CHARGE TIMES
AC150 VOLTAGE BATTERY SIZE CHARGE TIME
TYPE 12V 100-350CCA Maintenance
INPUT 12V 150-400MCA Maintenance
OUTPUT 12V 7-24Ah 10-30 hrs

Projecta's AC250B battery charger

12 Volt, 2.5 Amp, Automatic Battery Charger $59.95

Projecta's AC250B battery charger is a 12 Volt, 2.5 Amp automatic battery charger

suitable for use on 12 Volt lead acid batteries between 7-70Ah (Approx. 125-550CCA).

The charger is sonically sealed so that it can be mounted inside an engine bay. A hard wiring harness and mounting bracket are included for quick installation.

Alternatively, the charger can be operate from a bench using the 3 metre battery clip lead also supplied.

When the battery is fully charged, the charger will automatically stop charging and begin maintaining the battery in the fully charged state.

This allows the charger to be left connected indefinitely making it suitable for infrequently used batteries.

Built into the battery charger are a number of safety features, including soft start to prevent sparks on connection, polarity protection to prevent sparks from reverse connection or a direct short.

This battery charger is ideally suited for the maintaining of infrequently used batteries.

SPECIFICATIONS
PART NO. AC250B
TYPE Automatic
INPUT 240V, 50Hz, 28W
OUTPUT 1600mA (2.5A RMS*) at 12.0V
CHARGE CONTROL
Cut out: 14.2V
Cut in: 13.4V
Start: 5.0V
ApPROVALS Electrical Safety, EMC
L.E.D CHARGE INDICATION
RED LIGHT ON Power on and charging
WHEN SECOND
RED LIGHT
TURNS GREEN Fully charged and maintaining, no need to turn the charger off
BATTERY CHARGE TIMES
AC250B VOLTAGE BATTERY SIZE CHARGE TIME
AUTOMOTIVE 12V 200-650CCA Maintenace
MARINE 12V 250-700MCA Maintenace
DEEP CYCLE 12V 16-40Ah 10-30 hrs

JET SKIS

MOTOR CYCLES

MOTOR BIKES

SNOW MOBILES

SPORTS CARS

CONVERTIBLES

BOATS

TRACTORS

TRUCKS

DO YOU HAVE A TOY CAR \ BIKE THAT SITS IN THE SHED AND ONLY GETS TAKEN FOR A SPIN ONCE A MONTH UP IN THE HILLS TO A NICE RESTAURANT ,

AND THE LAST TIME YOU PLANNED THE DAY AND BOOKED THE TABLE AT THE RESTAURANT AND YOU GOT YOUR DATE AND JUST GOT IN THE TOY AND YOU PUT THE KEY IN THE IGNITION AND TURNED IT AND IT WENT CLICK..!!

AHHHHH WELL YOU SHOULD HAVE ONE OF THESE HOOKED UP..

JUST HOOK UP THE CHARGE AND MAINTAIN AND YOU WONT HAVE THIS PROBLEM AGAIN.....

JUST UN PLUG THE UNIT WHEN YOU WANT TO GO FOR A DRIVE AND WHEN YOU GET BACK PLUG IT BACK IN AND YOU WILL ALWAYS A FULLY CHARGED BATTERY IN YOUR TOY.......

‘ON BOARD’ BATTERY CHARGING (AC250B ONLY)
The AC250B ‘On Board’ charger allows the charger to be conveniently mounted on the vehicle.

The charger can be mounted to any flat surface using the mounting tabs or bolted to the supplied ‘L’ Bracket (Bolts, Washers & Nuts Supplied) and mounted next to the battery as per the diagram.

INTELLI-CHARGE
Battery Chargers
12V 7-Stage Switchmode
7 STAGE CHARGING
Intelligent electronics monitor the charging process to deliver an advanced 7 stage charge maximising battery performance and life.
MULTI CHEMISTRY
Set the charging profile to suit the battery’s chemistry type, extending the battery’s life.
POWER SUPPLY MODE
Operates as a power supply to run a 12V appliance. Ideal for retaining memory when changing a vehicle battery.

Available in:
P/No. IC700 $150.00
Intelli-Charge 12V 7A 7-Stage Battery Charger

P/No. IC1000 $ 175.00
Intelli-Charge 12V 10A 7-Stage Battery Charger

P/No. IC1500 $195.00
Intelli-Charge 12V 15A 7-Stage Battery Charger

7-STAGE AUTOMATIC CHARGING
Intelli-Charge battery chargers are fully automatic and protect your battery from being overcharged allowing you to leave the charger connected indefinitely. They are also
safe to use on batteries still connected to the vehicle without damaging sensitive vehicle electronics.
Using intelligent electronic control, Intelli- Charge battery chargers deliver a very
comprehensive and accurate charging technique known as 7-stage charging.

P/No.	IC700	IC1000	IC1500
Type	7 Stage	7 Stage	7 Stage
Input (Nominal)	240VAC, 50Hz	240VAC, 50Hz	240VAC, 50Hz
Input Power	216W	288W	408W
Output Voltage	12V	12V	12V
Output Current	7A	10A	15A
Minimum Start Voltage	2.5V	2.5V	2.5V
Back Drain	1 mA	1 mA	1 mA
CHARGE CONTROL
SPECIFICATIONS
	Desulphation	High Frequency Pulse charge up to 11 V
Soft Start	3.5A up to 12V	5.0A up to 12V	7.5A up to 12V
Bulk	7A up to:	10A up to:	15A up to:
14.1V (GEL)	14.1V (GEL)	14.1V (GEL)
14.4V (AGM)	14.4V (AGM)	14.4V (AGM)
14.7V (WET)	14.7V (WET)	14.7V (WET)
14.7V (CALCIUM)	14.7V (CALCIUM)	14.7V (CALCIUM)
Absorption	Constant voltage until current	Constant voltage until current	Constant voltage until current
drops to 1.05A	drops to 1.5A	drops to 2.25A
	Equalization	Constant current	Constant current	Constant current
	(Calcium mode only)	(2.0A) up to 16V	(2.0A) up to 16V	(2.2A) up to 16V
	then hold for 1 hour	then hold for 1 hour	then hold for 1 hour
	or 12 hour timeout	or 12 hour timeout	or 12 hour timeout
Analysis	Monitors battery for 90 sec
	Recondition	Constant current	Constant current	Constant current
	(1.05A) for 4 hours	(1.5A) for 4 hours	(2.25A) for 4 hours
	limited to:	limited to:	limited to:
	14.1V (GEL)	14.1V (GEL)	14.1V (GEL)
	14.4V (AGM)	14.4V (AGM)	14.4V (AGM)
	16V (WET)	16V (WET)	16V (WET)
	16V (CALCIUM)	16V (CALCIUM)	16V (CALCIUM)
Float	13.7V	13.7V	13.7V

Solar battery chargers
Part No: SCH01

125ma charger

Part No: SCH05

5W Solar Battery Charger $90.00
Both of these solar charges help prevent dead car batteries and expensive battery replacement.
Great for cars, 4WD’s and boats, especially those stored or parked for extended periods.

A maintenance level of charge is sent to the battery which means the battery will never be overcharged and this will extended the life of the battery as charge is constantly maintained.
Both include an LED voltage indicator and weatherproof casing.
We recommend the use of the WS777 power socket for direct connection to battery

Smart charger 6/12V
Part No: CHS125

This unit is suitable for charging/maintaining batteries in cars, trailers, boats and vans.

Designed to charge then maintain 12 volt lead acid, AGM or sealed lead acid batteries.

Reverse polarity/short circuit protection.
Output DC 12V 1.25A.

Steel mounting bracket.

Laptop Charger 3.5amp

Part No: CHC350

12 Volt cigarette lighter socket to power range of laptops
models by Acer, Compaq, HP, Sharp, IBM & Toshiba.

Maintenance charger 750ma

Part No: CHS075

This unit is suitable for charging/maintaining batteries in cars, trailers, boats and vans.

Designed to charge then maintain 12 volt lead acid, AGM or sealed lead acid batteries.

Output DC12V 0.75A

HANDYMAN RANGE

2700mA DC Battery Charger $28.95

The CH4 is an entry level charger and will charge most car & boat starting batteries overnight. It should not be left connected to a battery for more than 48 hours. Two LED’s indicators show when the unit is powered and when battery is fully charged. Not recommended for other than normal ‘starting batteries’.
Product Code: CH4

3500mA DC Battery Charger $49.95

The 3500mA charger fits nicely between the CH4 promotional unit & the CH6A 6 &12V model. It will charge most 12 volt starting batteries & has features that include LED charging & fully charged indicators. Short circuit protection, double insulation, durable plastic casing with carry handle and battery clamps with 120cm cables.
Product Code: CH5

4000mA DC Battery Charger $79.95

The CH6A is another entry level offering that will charge most 6 & 12 volt starting batteries. Can be left connected to power and battery in dry, well ventilated areas away from flammable goods and children. Will maintain a trickle charge 100Ma (1/10 of amp) when battery has been charged. 4 LEDs show state of charge (Charging - 50% - 75% - 100%) Will charge sealed lead acid and AGM deep cycle batteries but we recommend disconnecting from power once battery is charged. Features built in safety protection if charger is incorrectly connected to battery.
Product Code: CH6A

5400mA DC Battery Charger $89.95

The CH8A is another entry level offering that will charge most 6 & 12 volt starting batteries. Can be left connected to power and battery in dry, well ventilated areas away from flammable goods and children. Will maintain a trickle charge 100Ma (1/10 of amp) when battery has been charged. 4 LEDs show state of charge (Charging - 50% - 75% - 100%) Will charge sealed lead acid and AGM deep cycle batteries but we recommend disconnecting from power once battery is charged. Features built in safety protection if charger is incorrectly connected to battery.
Product Code: CH8A

Professional Range

12/6V 4000mA DC Battery Charger $99.00

The CH6A is another entry level offering that will charge most 6 & 12 volt starting batteries. Can be left connected to power and battery in dry, well ventilated areas away from flammable goods and children. Will maintain a trickle charge 100Ma (1/10 of amp) when battery has been charged. 4 LEDs show state of charge (Charging - 50% - 75% - 100%) Will charge sealed lead acid and AGM deep cycle batteries but we recommend disconnecting from power once battery is charged. Features built in safety protection if charger is incorrectly connected to battery. METAL CASE

Product Code: CHM6A

12/6V 7500mA DC Battery Charger $139.00

Now with a more accurate digital display! Sturdy metal cased charger capable of charging both 6 & 12 volt car, truck or boat starting batteries. Ideal for the serious car enthusiast. Twin LED’s indicate if battery is incorrectly connected to power & when battery is fully charged. When the 12V battery reaches 14.4 volts the charging ceases, though it will restart when the voltage drops below 13.8v. Ideal for maintaining starting and deep cycle 12V batteries in an optimum condition. Charger can be left connected to power & battery in dry, well ventilated areas away from flammable goods and children. METAL CASE
Product Code: CHM12A

12V 14000mA DC Battery Charger $160.00

Now with a more accurate digital display! This top of the range model is ideal for farmers, mechanics & truck drivers who require 12V charging. A heavy duty metal case, reverse polarity and short circuit protection are standard features. In addition the unit automatically maintains a 100mA 12V floating charge when a battery is fully charged. A green LED indicator illuminates when battery is fully charged. Trickle & fast charge modes are also available. This unit also has a 55,000mA jump starting feature that will provide enough power to start most 12V vehicles that have flat batteries.METAL CASE
Product Code: CHM20A

Battery Discharge Protector

Protect yourself against a flat battery! When the vehicles battery voltage falls below 11.5 Volts, the battery guard will automatically suspend power to any 12V accessory connected via the cigarette socket, saving enough battery power to start most vehicles.

Product Code: BDP01

Power Supply 7.5 amp

Part No: SB7975

This new power transformer is designed to power equipment that requires 12V DC power.

It converts 240V to 12V DC and can supply up to 7.5 amps of continuous power.
Features include a built in cooling fan, 8A circuit breaker with reset button, LED power indicators, C-Tick approved.

Ideal for use with most 12V powered accessories.

JUMPER LEADS

Jumper leads 400amp

Part No: SB400SG

Suitable for most under 4.5 litre 12V vehicles with electronic fuel injection.

PVC sheathed cable gives maximum power transfer.

Fitted with fully insulated clips.

Features built in surge protector to protect a vehicles electronics and computer system from power spikes during jump starts.
Length 3.0M

Jumper leads 500amp

Part No: SB500

Heavy Duty booster cables are suitable for 12V cars, 4WD’s and commercial vehicles. PVC sheathed cable gives maximum power transfer.

Fitted with fully insulated clips.
Length 4.0M.

Not suitable for vehicles with electronic fuel injection.

Part No: SB700SG

Heavy Duty booster cables are suitable for petrol and diesel,12V cars, 4WD’s and commercial vehicles. PVC
sheathed cable gives maximum power transfer. Fitted with fully insulated clips. Features built in surge protector to protect a vehicles electronics and computer system from power spikes during charging. Length 3.6 metres

PROJECTA

DBD070 $55.95

12/24V 70 Amp Diode Isolator

Preferred method for charging dual batteries on vehicles with externally sensed alternators Solid state and waterproof

FEATURES
Independent Charging
Diode isolators independently charge both batteries when the engine starts. This allows large auxiliary batteries to be used with a smaller starting battery as they are not paralleled during charging. Therefore, a very flat, large auxiliary battery can not flatten the
starting battery during charging.
Solid State
Diode isolators use solid state electronics and have no moving parts making them ultra reliable. As they don't use heavy duty switches, they don't produce voltage surges.
Dual Voltage (12/24V)
Diode isolators can be used on either 12V or 24V vehicles.
Waterproof
Diode isolators are completely waterproof making them ideal for marine environments.
Suits Vehicles with Externally Sensed Alternators
Common to all diode isolators is a voltage drop between the input and output terminals, it is 0.5V on the Projecta unit.

This voltage drop means that the charging voltage on the battery will be 0.5V less than the voltage coming from the alternator, which results in batteries being undercharged.

Vehicles with externally sensed alternators can connect the sensing wire directly to the battery. This makes the alternator produce an extra 0.5V on its output to compensate for the diode isolator.

SPECIFICATIONS
PART NO. DBD070
VOLTAGE 12V
CHARGING CURRENT 70A
CHARGE TYPE Independently charges both batteries
CONTROL Solid State
MOUNTING Surface/firewall

CURRENT DRAW 0mA
VOLTAGE DROP 0.5 Volt

SURGE PROTECTION Not required
(Diode does not create a surge)

LINK TO INSTRUCTIONS

DBD120 $69.95
12/24V 120 Amp Diode Isolator
Preferred method for charging dual batteries on vehicles with externally sensed alternators Solid state and waterproof

FEATURES
Independent Charging
Diode isolators independently charge both batteries when the engine starts. This allows large auxiliary batteries to be used with a smaller starting battery as they are not paralleled during charging. Therefore, a very flat, large auxiliary battery can not flatten the
starting battery during charging.
Solid State
Diode isolators use solid state electronics and have no moving parts making them ultra reliable. As they don't use heavy duty switches, they don't produce voltage surges.
Dual Voltage (12/24V)
Diode isolators can be used on either 12V or 24V vehicles.
Waterproof
Diode isolators are completely waterproof making them ideal for marine environments.
Suits Vehicles with Externally Sensed Alternators
Common to all diode isolators is a voltage drop between the input and output terminals, it is 0.5V on the Projecta unit.

This voltage drop means that the charging voltage on the battery will be 0.5V less than the voltage coming from the alternator, which results in batteries being undercharged.

Vehicles with externally sensed alternators can connect the sensing wire directly to the battery. This makes the alternator produce an extra 0.5V on its output to compensate for the diode isolator.

SPECIFICATIONS
PART NO. DBD120
VOLTAGE 12V/24V
CHARGING CURRENT 120A
CHARGE TYPE Independently charges both batteries
CONTROL Solid State
MOUNTING Surface/firewall

CURRENT DRAW 0mA
VOLTAGE DROP 0.5 Volt

SURGE PROTECTION Not required
(Diode does not create a surge)

ARLEC

Battery Chargers


BC269

Chargette 1000 Motorcycle Battery
Charger4
Plugs directly into 240 volt mains.

Output 6 and 12 volt 1 amp. Overload protection.

Will charge motorcycle and other small lead-acid batteries (approx 4 to 20 amp hour) overnight.
12 month warranty.

Arlec BC54

Heavy Duty 10000

Product Description
Heavy Duty 10000 Battery Charger

Charges 6 or 12 Volt
10 amp continuous (Hi), 5 amp continuous (Lo).
Hi/Lo charge switching.
Charge indication ammeter.
Two metre leads fitted with battery clips. 1.8 metre mains input lead.

Metal charger casing with handle buffers.
Overload, short circuit and reverse battery protected.
Suitable for charging typically small to medium automotive lead-acid batteries overnight (approx 30 to 160 amp hour).
Two Year Warranty

Battery Testers

Battery Hydrometer small

Battery hydrometer suitable for testing charge in small batteries.

Product Code: F101C

Battery Hydrometer large

Battery hydrometer suitable for testing charge in large batteries

Product Code: F202C

LED Battery Tester

LED indicators verify condition of battery and alternator. Suitable for 12Volt DC systems. Fitted with 300mm of cable and crocodile clips.

Product Code: BT100